Gel coat is the outer layer of fiberglass. Its structural value is not significant. However, it gives the product its shine and color. In addition, it offers protection to the hull. Read on to know more on how to restore faded fiberglass.
Because the product is exposed to various conditions over time, erosion of its outer layer is normal. This will leave it looking ugly. However, there is a way to fix this. Before you do anything else, you should ensure the surface is clean. You will need water, a sponge and detergent for this. It is better if the water is warm. Remember to protect your hands before starting the cleaning.
If there is mildew, you will have to add some bleach. Sometimes, stains are difficult to eliminate. You will have to apply a concentrated cleaner directly to the spot. Do not forget to rinse the surface thoroughly after the cleaning process. You can use a clean cotton cloth to dry the product or let it dry naturally.
Any oil present should be wiped off completely. Cleaning detergents cannot achieve this effectively. Thus, you must purchase MEK or acetone. You will have to get several cleaning clothes. Shy away from applying these formulations directly on the item. After this, you should wax the fiberglass. This is crucial because it preserves the fiberglass so that it can serve you for long.
The procedure of applying wax differs depending on the manufacturer. Therefore, you have to read the instructions given. Nevertheless, a foam pad or cloth is used in applying the wax. Proceed in circular motions. After the wax has dried, you should buff the excess using a soft piece of cloth.
Polishing follows waxing. Abrasives are needed for this task. Fine sandpaper is recommended. All pitted spots will be made smooth. Coating alone cannot achieve this. Dividing the surface in sections and tackling each at a time is advisable. Ensure you move in circles all the time. You ought to only stop when you can see your own image on the particular surface. Remember to apply a fresh coat of wax afterwards. Some polish preparations have wax.
Sometimes the product is worn significantly. In such a case, even polishing will not give back its shine. You will have to use a very strong abrasive during the scrubbing. You should remove any remaining wax on the surface before you begin polishing it. It can make the compound appear uneven. While clearing the wax, do not move up and down but rather on a straight line. Toluene or a de-waxing solution should be utilized.
A restorer is applied last. They are quite a number and you cannot fail to get a suitable one in the market. However, it acts just like wax. Nonetheless, there is no need to buff your fiberglass after you are done applying it. The end product is impressive. However, this effect will only last for a considerable duration if you take care of the product. Nonetheless, you will have to restore it after sometime.
Because the product is exposed to various conditions over time, erosion of its outer layer is normal. This will leave it looking ugly. However, there is a way to fix this. Before you do anything else, you should ensure the surface is clean. You will need water, a sponge and detergent for this. It is better if the water is warm. Remember to protect your hands before starting the cleaning.
If there is mildew, you will have to add some bleach. Sometimes, stains are difficult to eliminate. You will have to apply a concentrated cleaner directly to the spot. Do not forget to rinse the surface thoroughly after the cleaning process. You can use a clean cotton cloth to dry the product or let it dry naturally.
Any oil present should be wiped off completely. Cleaning detergents cannot achieve this effectively. Thus, you must purchase MEK or acetone. You will have to get several cleaning clothes. Shy away from applying these formulations directly on the item. After this, you should wax the fiberglass. This is crucial because it preserves the fiberglass so that it can serve you for long.
The procedure of applying wax differs depending on the manufacturer. Therefore, you have to read the instructions given. Nevertheless, a foam pad or cloth is used in applying the wax. Proceed in circular motions. After the wax has dried, you should buff the excess using a soft piece of cloth.
Polishing follows waxing. Abrasives are needed for this task. Fine sandpaper is recommended. All pitted spots will be made smooth. Coating alone cannot achieve this. Dividing the surface in sections and tackling each at a time is advisable. Ensure you move in circles all the time. You ought to only stop when you can see your own image on the particular surface. Remember to apply a fresh coat of wax afterwards. Some polish preparations have wax.
Sometimes the product is worn significantly. In such a case, even polishing will not give back its shine. You will have to use a very strong abrasive during the scrubbing. You should remove any remaining wax on the surface before you begin polishing it. It can make the compound appear uneven. While clearing the wax, do not move up and down but rather on a straight line. Toluene or a de-waxing solution should be utilized.
A restorer is applied last. They are quite a number and you cannot fail to get a suitable one in the market. However, it acts just like wax. Nonetheless, there is no need to buff your fiberglass after you are done applying it. The end product is impressive. However, this effect will only last for a considerable duration if you take care of the product. Nonetheless, you will have to restore it after sometime.
About the Author:
When you are looking for information about how to restore faded fiberglass, pay a visit to our web pages online here today. Additional details are available at http://www.leprechaunmagic.com now.
No comments:
Post a Comment